Start a project ↗

Product knowledge

Useful decisions. Better tool projects.

Practical product, OEM/ODM and quality guidance grounded in the tools and project work shown across this site.

Electric Screwdriver Spare Parts Service Plan; XOENAEN 53-in-1 precision electric screwdriver set shown as a product configuration referenceOctober 30, 2026Electric Screwdriver Spare Parts Service PlanRead article →
098Deburring a 3D Printed Perforated Filter Plate Without Joining Holes using the XOENAEN H102 five-speed cordless engraving pen as a documented product reference
August 31, 2026 · XOENAEN 3D Print & DIY Application Team

Deburring a 3D Printed Perforated Filter Plate Without Joining Holes

Compare each suspect opening with a retained reference and clear only material inside its boundary. Support the work with a flat perforated backing that supports ligaments while allowing debris to escape. Control hole count, guide size, plate support, vibration and debris collection. Stop when two openings begin to merge, a ligament whitens or the plate develops a local wave.

Read article →
099Deburring a T-Slot Aluminum Extrusion Cut End for Square Assembly using the XOENAEN D-102 cordless engraving pen as a documented product reference
August 31, 2026 · XOENAEN 3D Print & DIY Application Team

Deburring a T-Slot Aluminum Extrusion Cut End for Square Assembly

Check squareness and length first, then remove only raised burrs outside the mating plane. Support the work with a soft-jaw vise holding the profile close to the cut without marking the anodized faces. Control profile support, face squareness, accessory direction, edge color and swarf control. Stop when the anodized border widens, the face loses full contact or the slot mouth becomes bell-shaped.

Read article →
100Polishing Small Brass Hardware Before a Clear Protective Coat using the XOENAEN D-104 cordless engraving pen as a documented product reference
August 31, 2026 · XOENAEN 3D Print & DIY Application Team

Polishing Small Brass Hardware Before a Clear Protective Coat

Identify solid brass versus plating and approve the target sheen on a hidden area. Support the work with a padded pin fixture that supports the hardware without covering the visible face. Control material identity, compound, pad cleanliness, dwell, edge contact and residue removal. Stop when the color changes unevenly, plating thins or compound packs into engraving.

Read article →
101Shaping a Balsa Model Airfoil Leading Edge Without Flat Spots using the XOENAEN D-106 cordless engraving pen as a documented product reference
August 31, 2026 · XOENAEN 3D Print & DIY Application Team

Shaping a Balsa Model Airfoil Leading Edge Without Flat Spots

Use section templates to establish the target before choosing any powered removal. Support the work with a full-span cradle supporting the wing without twisting spars or ribs. Control grain direction, spanwise support, template stations, dust and removal sequence. Stop when the surface ripples between ribs, grain tears or a template shows a local hollow.

Read article →
102Flush-Trimming a Dowel in Miniature Furniture Without Dishing Wood using the XOENAEN H101 five-speed cordless engraving pen as a documented product reference
August 31, 2026 · XOENAEN 3D Print & DIY Application Team

Flush-Trimming a Dowel in Miniature Furniture Without Dishing Wood

Remove most of the projection with a protected hand cut before introducing abrasive contact. Support the work with a flat padded bench support with masking around the joint. Control grain direction, glue cure, backing hardness, local pressure and surface protection. Stop when the surrounding wood turns lighter, veneer lifts or the joint area becomes concave.

Read article →
103Deburring a Drilled PETG Sheet Panel Without Starting Edge Cracks using the XOENAEN H102 five-speed cordless engraving pen as a documented product reference
August 31, 2026 · XOENAEN 3D Print & DIY Application Team

Deburring a Drilled PETG Sheet Panel Without Starting Edge Cracks

Measure the finished opening and support both faces before removing the raised lip. Support the work with a clean flat backer with a relief opening beneath the drilled feature. Control sheet temperature, back support, tool axis, edge distance and protective film. Stop when the hole turns oval, a white stress line appears or the panel surface starts to smear.

Read article →

Project inquiry

Bring us the brief.

Share your product, market, quantity and customization requirements. Our project team will reply with the right next step.

Request a sample ↗WhatsApp +86 189 2743 5868